www.kitcarecorp.com info@kitcarecorp.com 494 Call us today at 1-800-387-1858 or 416-243-3030 Circuit Breaker Lockouts L2-CB01 L2-CB02 L2-CB03 L2-CB04 1 2 3 1 2 3 1 2 A D C B A D C B 1 2 3 A D C B A D C B Constructed of rigid plastic, the new C-SAFEcircuit breaker lockouts are now available for eithersingle or double pole circuit breaker lockout applications. Sold in packs of 6. A single pole lockout, CB01 requires a switch breaker with a recessed hole in it. Our double pole breaker lockout requires that there be two toggles connectedtogetherwith a cross bar. 1 • To install,place over the toggles with the slotted side of the lockout covering the toggles. 2 • Pull the slide bar out to attach your lock. This model will accommodate breakers with an overall width of 5/8” (45mm). Remember, the breaker must be in the“off” position before installing. A single pole lockout, CB03 does not require a switch breaker with a recessed hole in it. Our double pole circuit breaker lockout CB04 will fit most major brands of elec- trical circuit breakers. If this lockout does not fit, it may be returned. Our single pole breaker lockout requires a single toggle with a recessed hole in it. 1 • To install,simplyopen the lock by slidingthe base of the lock backwards. 2 • Place over the toggle, making sure that the small pole insidethe lockout device is now inserted into the hole of the toggle. Close the lockout by pushing the base foward after ensuring that the holes are aligned. 3 • You are now ready to installyour lock. This model will accommodate breakers up to 9/16” (14mm.) in width. Remember, the breaker must be in the“off” position before installing. Our double pole breaker lockout requires that there be two toggles connected togetherwith a cross bar. 1 • Pull the sliderbar and place the breaker lockout over the breakers. 2 • Push back the sliderbar and put your lock on aligned holes. This model will accommodate double or triple breakers . Remember, the breaker must be in the "off " position before installing. This model is our single breaker lockout for circuit breakers that do not have a recessed hole. 1 • To install,the breaker must be in the“off” position. Place the breaker over the toggle. 2 • Insert your screwdriver (star type) into the hole, tighten the screws well. 3 • Insert your lock or tag and close. Make sure everything is tight. This model will accommodate circuit breakers with an overall width of 9/16”(14mm). Remember, the breaker must be in the“off” position before installing. E-SAFE "LOCK-A-SWITCH" This easy to installdevice can be used with most mounted switches.It can be used to lock the switch in eitherthe“on” or“off” position. (Install using existing screws). CIRCUIT BREAKER LOCKOUTS The CB02, is a double pole lockout and requires the breakers to be connectedwith a cross bar for lockout application. ELECTRICAL SWITCH LOCKOUT Remove screws from switch plate. Adjust“E-SAFE” locking device over the switch plate and installit on switch. Position switch to desired position. Close“E-SAFE” device and put on your padlock and tag. L2-CB02 L2-CB02 L2-CB03 L2-CB03 L2-CB04 L2-CB04 L2-CB01 L2-CB01 L2-ES01 L2-CB01 L2-CB02 L2-CB03 L2-CB04 ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS DIMENSIONS: C-SAFE CIRCUIT BREAKER LOCKOUTS TECHNICAL DATA DIMENSIONS: E-SAFE LOCK-A-SWITCH TECHNICAL DATA THE ULTIMATE PROTECTION WITH THE E-SAFE LOCK-A-SWITCH Models Length Height Width Lock Hole A B C D 2.300” 0.850” 1.100” 0.300” dia. 58mm. 22mm. 28mm. 7.5mm. 2.625” 1.875” 1.000” 0.300” dia. 66mm. 48mm. 25mm. 7.5mm. 2.300” 0.750” 1.000” 0.340” dia. 58mm. 19mm. 25mm. 8.5mm. 2.375” 1.000” 1.865” 0.375” dia. 60mm. 25mm. 47.5mm. 9.5mm. 3.000” 1.625” 3.000” 76mm. 42mm. 76mm. Models Height Width Width Close Open A B C 1 1 4 4 3 3 2 2